National codes and design standards in Advance Design | GRAITEC CANADA

National codes and design standards in Advance Design

See the structural design standards available in Advance Design, including Eurocodes with National Annexes, ACI, AISC, CSA, ASCE, NTC and seismic, wind, snow, concrete, steel, timber, composite and masonry workflows.

Get a free trial

Structural design is not only about creating a model and running calculations. Every project must also be checked against the right design standards for its location, material, loading conditions and regulatory requirements.

Advance Design helps structural engineers connect FEM analysis, load generation, code-based design checks, optimization and reporting in one workflow. Within that workflow, national codes and design standards control how load combinations are generated, how climatic and seismic actions are defined, and how reinforced concrete, steel, timber, masonry and composite elements are verified.

This page explains which standards are available in Advance Design, how to understand the difference between Eurocodes, National Annexes and national codes, and how to choose the right standard for your project.

What are national codes in structural design software?

National codes are structural design rules used to verify whether a building or civil engineering structure satisfies the required safety, serviceability and durability criteria. They define how loads are combined, how environmental actions such as wind and snow are calculated, how seismic forces are considered, and how structural members are checked for each material.

In Advance Design, these standards are configured at project level through the Localization Configuration settings. Depending on the selected localization, the software applies the relevant standards for combinations, seismic actions, climatic actions, reinforced concrete, steelwork, timber, masonry and other design workflows.

National codes and design standards in Advance Design | GRAITEC CANADA

This matters because the selected standard can affect:

  • load combination rules;
  • wind and snow load generation;
  • seismic load families and response spectrum parameters;
  • concrete, steel, timber, masonry and composite design checks;
  • safety factors and National Annex values;
  • material libraries and cross-section data;
  • calculation reports and documentation.

Eurocodes, National Annexes and national standards: what is the difference?

Many European projects are designed using the Eurocodes. However, the Eurocodes are often used together with a National Annex, which adapts certain parameters for a specific country.

Other regions use independent national standards. For example, the United States commonly uses ASCE for actions, ACI for concrete and AISC for steel, while Canada uses National Building Code / Canadian standards and CSA material design standards.

Type of standard What it means Examples in Advance Design
Eurocode with National Annex A Eurocode framework adapted with country-specific parameters EC0, EC1, EC2, EC3, EC5, EC6, EC8 with National Annexes for selected countries
Independent national code A separate national code family, not a Eurocode annex ASCE 7, ACI 318, ANSI/AISC 360, CSA S16, CSA A23.3, CSA O86, NBC
Local or legacy national rule A country-specific standard used for selected workflows or existing design practice BAEL91, CM66, NV65/NV2009, PS92, P100, RPS 2011, RPA99-2003, CR0/CR1/CR6
Material or profile standard A library or specification used for materials and cross-sections EN 10025, EN 10210, EN 10219, AISC, CISC, European profiles, North American profiles

 

Which standard should I use in Advance Design?

The right standard depends first on the project location and the design requirement. A roof wind load problem, for example, is not a concrete design problem. It belongs to climatic actions, so the relevant family is EC1 / EN 1991-1-4 or the applicable national wind standard.

Project requirement Standard family to check Typical use in Advance Design
Load combinations EC0, ASCE, Canadian code family, NTC, BAEL, CM66, CR0 ULS/SLS combinations and concomitance rules
Wind and snow loads EC1, ASCE 7, Canadian code family, NTC, NV65/NV2009, CR1 Automatic wind and snow generation, roof pressure zones, snow accumulation
Seismic analysis EC8, NBC, ASCE/IBC, NTC, PS92, P100, RPS, RPA Seismic load case families, response spectrum settings, modal spectral analysis
Reinforced concrete design EC2, ACI 318, CSA A23.3, NTC, BAEL RC beams, columns, walls, slabs and footings
Steel design EC3, ANSI/AISC 360, CSA S16, NTC, CM66 Steel member checks, stability, optimisation and shape sheets
Composite steel-concrete design EC4, AISC 360-16 Composite beams and floor decks
Timber design EC5, CSA O86, NDS, NTC Timber member verification, deflection, buckling, fire and optimisation
Masonry design EC6, NTC 2018, CR6-2013 Masonry wall verification
Material selection EN, ACI, CSA, NTC and other material references Material libraries for steel, concrete, timber and masonry
Cross-section selection AISC, CISC, European and North American profiles Profile libraries and structural section data

 

Example: which standard applies to roof wind loads?

If you are checking wind actions on a roof, the relevant standard is a climatic action standard, not a material design standard.

For Eurocode projects, wind actions are covered by Eurocode 1, particularly EN 1991-1-4, with the applicable National Annex. In Advance Design, this belongs to the climatic actions workflow, where wind and snow load families are generated according to the selected standard.

For a UK project, for example, you would select the Eurocode 1 climatic standard with the United Kingdom National Annex where required by the project specification. For a US project, the corresponding workflow would use ASCE 7 wind provisions. For a Canadian project, the corresponding Canadian climatic standard should be selected.

The same principle applies to snow. Snow is a climatic action, so it should be configured through the climatic load family, not through concrete, steel or timber design settings.

Where are standards configured in Advance Design?

Advance Design standards are selected in the Localization Configuration dialog. This is where users define the interface and report language, localization settings, and the design standards that will be used for new projects.

In practice, use this workflow:

  1. Before starting a project, open the Localization Configuration dialog.
  2. Select the required localization and standards for the project.
  3. Confirm the standards for combinations, seismic actions, climatic actions, reinforced concrete, steelwork, timber and masonry.
  4. Create the project and define load cases, combinations and design assumptions.
  5. During the project, check the selected standards in the Localization Settings dialog or from the status bar.

Available standards in Advance Design

The lists below organize the available standards by engineering workflow. This makes it easier to identify the standard required for a specific task, such as generating wind loads, creating load combinations, checking steel members or designing masonry walls.

Load combinations standards

Load combination standards define how actions are combined for ultimate limit states, serviceability limit states and other design situations.

Use this section when the project requirement is about how actions should be combined, not how an individual material should be designed.

Standard Region / country
EC0 with National Annexes France, Great Britain, Germany, Portugal, Romania, Poland, Spain, Slovakia, Czech Republic
CBN 2010 Canada
CBN 2015 Canada
ASCE 7-10 USA
ASCE 7-16 USA
NTC 2008 Italy
NTC 2018 Italy
BAEL 91 France
CM66 France
CR0-2012 Romania

 

Climatic actions: wind and snow standards

Climatic standards control wind and snow load case families. These are the standards to use when calculating wind pressure on facades and roofs, snow loads, roof-specific climatic effects and related load generation.

Use this section for:

  • automatic wind load generation;
  • automatic snow load generation;
  • roof wind pressure cases;
  • duopitch roof, canopy roof, lattice structure, scaffolding and facade wind examples;
  • climatic National Annex settings.
Standard Region / country
EC1 with National Annexes France, Great Britain, Germany, Portugal, Romania, Poland, Spain, Slovakia, Czech Republic
CBN 2010 Canada
CBN 2015 Canada
ASCE 7-10 USA
ASCE 7-16 USA
ASCE 7-22 USA
NTC 2008 Italy
NTC 2018 Italy
NV65-84/2009 / NV2009 France
CR1-1-3/CR1-1-4 (2012) Romania

 

Reinforced concrete structural design standards

Concrete design standards are used for reinforced concrete elements and design modules such as beams, columns, walls, slabs and footings.

Use this section when checking concrete members or generating reinforcement calculations and RC design documentation.

Standard Region / country
EC2 with National Annexes France, Great Britain, Germany, Portugal, Romania, Poland, Spain, Slovakia, Czech Republic
CAN/CSA A23.3-14 Canada
ACI 318-14 USA
NTC 2008 Italy
NTC 2018 Italy
BAEL91 France

 

Steel structural design standards

Steel design standards are used for steel member verification, stability checks, cross-section classification, member optimisation and steel design reports.

Use this section for steel-framed buildings, steel members, stability verifications, steel optimisation, cold-formed member workflows and steel design result interpretation.

Standard Region / country
EC3 with National Annexes France, Great Britain, Germany, Portugal, Romania, Poland, Spain, Slovakia, Czech Republic
CAN/CSA S16-09 Canada
CAN/CSA S16-14 Canada
CAN/CSA S16-19 Canada
ANSI/AISC 360-10 (ASD & LRFD) USA
ANSI/AISC 360-16 (ASD & LRFD) USA
NTC 2008 Italy
NTC 2018 Italy
CM66 France

 

Composite steel-concrete structural design standards

Composite design applies to structural elements where steel and concrete act together, such as composite beams and floor decks. In Advance Design, composite linear elements are steel-based I-shaped beams classified as composite beams, and the composite standard must remain synchronized with the steel standard.

Use this section for composite beams, composite floor decks, shear connector design, effective width settings, construction-stage checks and final-stage composite verification.

Standard Region / country
EC4 – General General Eurocode workflow
EC4 – France France
EC4 – United Kingdom United Kingdom
EC4 – Romania Romania
EC4 – Germany Germany
EC4 – Czech Republic Czech Republic
EC4 – Poland Poland
EC4 – Slovakia Slovakia
EC4 – Spain Spain
EC4 – Portugal Portugal
AISC 360-16 USA

 

Timber structural design standards

Timber design standards are used for timber member verification, deflection checks, resistance checks, buckling, lateral-torsional buckling, fire resistance and timber shape optimisation.

Use this section for timber beams, columns and other timber linear elements where member resistance, stability, deflection or fire checks are required.

Standard Region / country
EC5 with National Annexes France, Great Britain, Germany, Portugal, Romania, Poland, Spain, Slovakia, Czech Republic
CSA O86-19 Canada
NDS 2018 (ASD and LRFD) USA
NTC 2008 Italy
NTC 2018 Italy

 

Masonry structural design standards

Masonry standards are used in the Masonry Wall module, where masonry walls are modelled as vertical planar shell elements and verified according to the selected masonry design standard.

Use this section for masonry wall verification, including walls with or without openings, masonry unit and mortar definition, and detailed or simplified masonry calculation workflows.

Standard Region / country
EC6 with National Annexes France, Great Britain, Germany, Romania, Poland, Spain, Portugal, Slovakia, Czech Republic
NTC 2018 Italy
CR6-2013 Romania

 

Seismic analysis standards

Seismic standards control the seismic load case families, spectrum settings and related modal spectral analysis parameters.

Use this section for seismic load generation, response spectrum analysis, modal spectral analysis, damping correction, accidental torsion and seismic load combinations.

Standard Region / country
EC8 with National Annexes France, Romania, Germany, Portugal, Spain, Slovakia, Czech Republic
NBC 2010 Canada
NBC 2015 Canada
NBC 2020 Canada
ASCE 7-10 / IBC 2012 USA
ASCE 7-16 / IBC 2018 USA
IBC 2012 USA
NTC 2008 Italy
NTC 2018 Italy
PS92 France
PS92-2010 France
P100/2006 Romania
P100-1/2013 Romania
RPS 2011 Morocco
RPA99-2003 Algeria

 

Material standards and libraries

Material standards and libraries help define the properties used for structural elements. Advance Design includes material references for steel, concrete, timber and masonry.

Material type Supported references
Steel AISC ASTM, CAN/CSA CISC G40, EN 10025 2-6, EN 10210-1, EN 10219-1, BS EN 1993-1-1, NF EN 10025 2-6 for buildings, NF EN 10025 2-6 for other structures
Concrete ACI 318 & 318M, CAN/CSA A23, EN 206, NFB18-406, STAS 10107/0-90, NTC
Timber EN 14080-1 for glued timber, EN 14374/14279 for veneer plywood, EN 338/2016 for softwoods and hardwoods, NP 005, CSA O86-19 for glue-laminated timber, SCL and sawn lumber, NDS 2018 for glue-laminated timber and sawn lumber
Masonry EN 1996

 

Cross-section libraries

Cross-section libraries provide the profile data used for structural members. Advance Design includes standard and regional profile libraries, and users can also define, import and export custom cross-sections.

Supported cross-section libraries include:

  • AISC;
  • CISC;
  • European profiles;
  • OTUA profiles;
  • Advance Steel database profiles;
  • North American profiles.

Advance Design also includes a Cross Sections module for defining custom sections, calculating section properties and exporting calculated sections to the Advance Design user sections library.

Structural design standards by country or region

This section helps users search by project location. Always confirm the required code with the client, local authority and project specification before selecting the project standard.

Europe: Eurocodes and National Annexes

For many European projects, Advance Design supports Eurocodes with National Annexes. Depending on the design task, these include:

  • EC0 for basis of design and load combinations;
  • EC1 for wind and snow climatic actions;
  • EC2 for reinforced concrete design;
  • EC3 for steel design;
  • EC4 for composite steel-concrete design;
  • EC5 for timber design;
  • EC6 for masonry design;
  • EC8 for seismic analysis.

National Annex coverage varies by workflow, but the available standards include support for countries such as France, Great Britain / United Kingdom, Germany, Portugal, Romania, Poland, Spain, Slovakia and Czech Republic.

France

French workflows in Advance Design include Eurocode National Annexes and selected French standards, including BAEL91 for concrete, CM66 for steel and combinations, NV65/NV2009 for climatic actions, and PS92 / PS92-2010 for seismic analysis. Use these standards when working on French projects that require French National Annexes or legacy French design rules.

United Kingdom

Advance Design includes Eurocode National Annex support for United Kingdom across several workflows, including load combinations, climatic actions, concrete, steel, timber and composite design. Use these standards when a UK project requires Eurocode-based design with the UK National Annex.

Germany

Advance Design includes German National Annex support for Eurocode-based workflows, including load combinations, wind and snow actions, concrete, steel, timber, composite and seismic analysis. Use these standards when the project specification requires German National Annex parameters.

Romania

Romanian workflows in Advance Design include Eurocode National Annex support and national Romanian standards such as CR0-2012 for combinations, CR1-1-3/CR1-1-4 for climatic actions, CR6-2013 for masonry and P100/2006 or P100-1/2013 for seismic analysis.

Italy

Italian workflows include NTC 2008 and NTC 2018 across several design areas, including combinations, climatic actions, concrete, steel, timber, masonry and seismic analysis. Use NTC standards when the project is located in Italy or where the project specification requires Italian national standards.

Canada

Canadian workflows include CBN 2010 / CBN 2015 for combinations and climatic actions, NBC 2010 / NBC 2015 / NBC 2020 for seismic workflows, CAN/CSA A23.3-14 for reinforced concrete, CAN/CSA S16-09 / S16-14 / S16-19 for steel and CSA O86-19 for timber. Use these standards for Canadian projects or projects requiring Canadian structural design rules.

United States

US workflows include ASCE 7-10, ASCE 7-16 and ASCE 7-22 for selected load and climatic workflows, ACI 318-14 for reinforced concrete, ANSI/AISC 360-10 and ANSI/AISC 360-16 for steel, AISC 360-16 for composite design, NDS 2018 for timber, and ASCE/IBC seismic workflows. Use these standards when the project is located in the United States or where US design codes are specified.

Morocco and Algeria

Advance Design includes RPS 2011 for Moroccan seismic workflows and RPA99-2003 for Algerian seismic workflows. Use these standards where local seismic code compliance is required.

How national codes affect the Advance Design workflow

Selecting the right standard is not an isolated setup task. It affects the complete analysis and design workflow.

1. Model setup
The selected localization influences available material types, design assumptions and properties used by structural elements.

2. Load cases and combinations
Load combinations depend on the selected combination standard. If safety factors or design assumptions are changed after combinations have been generated, combinations may need to be regenerated.

3. Climatic load generation
Wind and snow load families are created according to the selected climatic standard. This affects wind regions, snow regions, exposure categories, roof parameters, pressure coefficients and other local code parameters.

4. Seismic load generation
Seismic load case families are created according to the selected seismic standard. This affects spectrum definitions, site class, importance category, behaviour factors and modal analysis parameters.

5. Material design checks
Concrete, steel, timber, masonry and composite elements are checked according to their selected standards and National Annexes. The standard affects resistance checks, deflection checks, stability checks, reinforcement assumptions and design reports.

6. Reporting
Calculation reports should reflect the selected standards, assumptions, load cases, combinations, results and design checks. This improves traceability and helps reviewers understand which regulatory framework was used.

Practical guidance for selecting structural analysis standards

Use this checklist before starting a project in FEA software Advance Design:

1. Confirm the project location. The location usually determines the applicable national rules.

2. Check the contract and authority requirements. The project brief may require a specific standard even if the project location suggests another.

3. Separate load standards from material standards. Wind, snow and seismic actions are not the same as concrete, steel, timber or masonry design.

4. Use the relevant National Annex where required. For Eurocode projects, the National Annex can change important parameters.

5. Set standards before generating combinations. Combination rules and safety factors should be configured before combinations are created.

6. Verify the selected standards before reporting. Use the Localization Settings dialog or status bar to confirm the project standards.

7. Document assumptions in the calculation report. Reports should make the selected standard, load cases and design checks clear.

National codes and design standards in Advance Design | GRAITEC CANADA

ARE YOU READY TO TRY ADVANCE DESIGN?

GET STARTED FOR FREE

Advance Design is engineered to meet the specific needs of structural engineers, offering powerful FEM capabilities that streamline their workflow.

Download your free trial

 

 

FAQs

  • Advance Design supports Eurocodes with selected National Annexes, North American standards such as ASCE, ACI, AISC, CSA and NBC, Italian NTC standards, French standards such as BAEL, CM66, NV and PS92, Romanian CR and P100 standards, and selected seismic standards for Morocco and Algeria.

  • Yes. Advance Design supports Eurocodes across multiple workflows, including EC0 for combinations, EC1 for climatic actions, EC2 for concrete, EC3 for steel, EC4 for composite design, EC5 for timber, EC6 for masonry and EC8 for seismic analysis. National Annex availability depends on the workflow.

  • EC1 is used for actions on structures, including wind and snow loads. EC2 is used for concrete design. If you are calculating wind loads on a roof, you should look at the climatic actions workflow under EC1, not the concrete design workflow under EC2.

  • Use the climatic action standard required by the project location and specification. For Eurocode projects, wind actions are covered by Eurocode 1, especially EN 1991-1-4, with the applicable National Annex. For US projects, use the relevant ASCE 7 climatic standard. For Canadian projects, use the relevant Canadian climatic standard.

  • Advance Design supports EC2 with National Annexes for selected countries, CAN/CSA A23.3-14, ACI 318-14, NTC 2008, NTC 2018 and BAEL91.

  • Advance Design supports EC3 with National Annexes for selected countries, CAN/CSA S16-09, CAN/CSA S16-14, CAN/CSA S16-19, ANSI/AISC 360-10, ANSI/AISC 360-16, NTC 2008, NTC 2018 and CM66.

  • Yes. Advance Design supports timber design using EC5 with National Annexes for selected countries, CSA O86-19, NDS 2018, NTC 2008 and NTC 2018.

  • Yes. The Masonry Wall module supports EC6 with selected National Annexes, NTC 2018 and CR6-2013.